Manual do usuário JOSSIL FINE VISION SRE-300 C

[. . . ] ) STATUS DATA 1100nnnn Cn Program change 0nnnnnnn nn Program number (0-127) Formula for converting Control values into parameter data: paramSteps= paramMax - paramMin + 1; add= paramWidth / paramSteps; mod= paramWidth - add * paramSteps; curValue= parm * add + mod / 2; (1) When the assigned parameter can be set in 128 steps or less: paramWidth = 127; rxValue = Control value; (2) When the assigned parameter can be set in 128 through 16383 steps: paramWidth = 16383; (2-1) When both High and Low data are received: rxValue = Control value (High) * 128 + Control value (Low); (2-2) When only Low data is received: rxValue = (curValue & 16256) + Control value (Low); (2-3) When only High data is received: rxValue = Control value (High) * 128 + (curValue & 127); (3) When the assigned parameter can be set in 16384 through 2097151 steps: paramWidth = 2097151; (3-1) When High, Middle, and Low data are received: rxValue = Control value (High) * 16384 + Control value (Middle) * 128 + Control value (Low); (3-2) When only Low data is received: rxValue = (curValue & 2097024) + Control value (Low); (3-3) When only Middle data is received: rxValue = (curValue & 2080895) + Control value (Middle) * 128; (3-4) When only High data is received: rxValue = (curValue & 16383) + Control value (High) * 16384; (3-5) When Middle and Low data are received: rxValue = (curValue & 2080768) + Control value (Middle) * 128 + Control value (Low); (3-6) When High and Low data are received: rxValue = (curValue & 16256) + Control value (High) * 16384 + Control value (Low); (3-7) When High and Middle data are received: rxValue = (curValue & 127) + Control value (High) * 16384 + Control value (Middle) * 128; if ( rxValue > paramWidth) rxValue = paramWidth; param = ( rxValue - mod / 2) / add; 5 MIDI TIME CODE QUARTER FRAME(F1) Reception This is echoed if [OTHER COMMANDS ECHO] is ON. [. . . ] STATUS 11111010 FA Start If [NRPN] is selected STATUS 1011nnnn 01100010 0vvvvvvv 1011nnnn 01100011 0vvvvvvv 1011nnnn 00000110 0vvvvvvv 1011nnnn 00100110 0vvvvvvv Bn 62 vv Bn 63 vv Bn 06 vv Bn 26 vv Control changeDATA NRPN LSB LSB of parameter number Control change*1 NRPN MSB MSB of parameter number Control change*1 MSB of data entry MSB of parameter data Control change*1 LSB of data entry LSB of parameter data 9. SYSTEM RESET (FF) Conversion from actual data into bulk data d[0~6]: actual data b[0~7]: bulk data b[0] = 0; for( I=0; I<7; I++){ if( d[I]&0x80){ b[0] |= 1<<(6-I); } b[I+1] = d[I]&0x7F; } Restoration from bulk data into actual data d[0~6]: actual data b[0~7]: bulk data for( I=0; I<7; I++){ b[0] <<= 1; d[I] = b[I+1]+(0x80&b[0]); } Reception When this message is received, MIDI communications will be cleared, e. The data area is handled by converting seven words of 8-bit data into eight words of 7-bit data. 0ddddddd dd data : : 11110111 F7 End of exclusive 0bbbbbbb bl 0ttttttt th total block number (minimum number is 0) *) For parameters with a data size of 2 or more, data for that size will be transmitted. 0ddddddd dd data : : 11110111 F7 End of exclusive *) For parameters with a data size of 2 or more, data for that size will be transmitted. When the data is received, the Automix Status data is transmitted on the [Rx CH] every second for 10 seconds. [. . . ] 0ddddddd dd data : : 11110111 F7 End of exclusive *) For parameters with a data size of 2 or more, data for that size will be transmitted. [. . . ]